玻璃加工需要用到各种玻璃机械设备，立式玻璃钻铣机就是其中常见的一种。玻璃钻孔机操作比较简单，只需输入参数，按下启动按钮就可以自动完成。但是玻璃钻孔机一旦出现问题就会影响到正常生产，所以日常的维护与保养非常重要，接下来玻多多小编就讲一下立式玻璃钻铣机日常维护方法。
Glass processing needs to use a variety of glass machinery and equipment, vertical glass drilling and milling machine is one of the common. The operation of glass drilling machine is relatively simple, just input parameters and press the start button to complete automatically. But once the glass drilling machine has problems, it will affect the normal production, so the daily maintenance is very important. Next, we will talk about the daily maintenance method of vertical glass drilling and milling machine.
1、钻轴和接头头的轴承装有防尘罩和密封圈。工作三个月后，这些轴承应加注润滑脂(在机电维修和操作员的配合下)；
1. The bearing of drill shaft and joint head is equipped with dust cover and sealing ring. After working for three months, these bearings should be filled with grease (with the cooperation of mechanical and electrical maintenance and operators);
2、其他主动摩擦部件要按时用油润滑(一天两次)(操作人员)；
2. Other active friction parts should be lubricated with oil on time (twice a day) (operator);
3、油雾喷射器应根据油位加注机油，以保证气缸的润滑供应。加油时注意不要太满，使用20号机油。油位在两条划线中间；

3. The oil mist injector should be filled with oil according to the oil level to ensure the lubrication supply of the cylinder. Pay attention not to be too full when refuelling, use No. 20 engine oil. The oil level is between the two lines;

4、拆开主轴套筒半年，在轴承内部涂上润滑脂；
4. Remove the spindle sleeve for half a year and apply grease inside the bearing;
5、所有钻机必 须每年清洗一次，并进行维护、加油、检查、更换等。(机电维修)；
5. All drilling rigs must be cleaned once a year and maintained, refueled, inspected and replaced（ Mechanical and electrical maintenance);
6、钻井过程中冲程和速度的调整主要由操作人员进行，电路每3-6个月检查一次，以防止电路故障；
6. The adjustment of stroke and speed during drilling is mainly carried out by operators, and the circuit is checked every 3-6 months to prevent circuit failure;
7、注意玻璃钻孔机电机的冷 却油，只能使用五分钟以上；
7. Pay attention to the cooling oil of the glass drilling machine motor, which can only be used for more than five minutes;
8、玻璃钻油必不可少，否则丝锥磨损开裂的概率会高很多。当需要注意用油时，不能用其他一般的油代替，要用专用油；
8. Glass drilling oil is essential, otherwise the probability of tap wear and cracking will be much higher. When you need to pay attention to the use of oil, you can not use other general oil instead of special oil;
9、气动马达需要清洗。因为气候很热，压缩空气中的水分会随着水分的增加而增加。在防水的前提下，要注意启动电机的清洁；
9. The pneumatic motor needs cleaning. Because the climate is very hot, the moisture in the compressed air will increase with the increase of moisture. On the premise of waterproof, pay attention to the cleaning of starting motor;
10、注意支架的平行度和平直度要求。它需要知道如何调整支架和直线度；如果支架不直，会导致水龙头无法移动和破裂;扭矩需求维修卡盘，卡盘是一种损耗产品，在一定的湿度下，我们需要知道如何调节扭矩，这样才能使钻具更稳定，不容易折断水龙头；
10. Pay attention to the parallelism and straightness of the bracket. It needs to know how to adjust the bracket and straightness; If the support is not straight, the faucet will not move and break; The torque needs to maintain the chuck. The chuck is a kind of loss product. Under certain humidity, we need to know how to adjust the torque, so as to make the drilling tool more stable and not easy to break the faucet;
11、每次操作完成后，清理碎玻璃和水渍等碎片，以防止机器生锈和图像下次被使用；
11. After each operation, clean the broken glass and water stains to prevent the machine from rusting and the image from being used next time;
12、定期保养零件，定期擦拭涂抹保养液，保持机器完好，特别是长时间不用时，要防止机器受潮损坏；
12. Maintain the parts regularly, wipe and smear the maintenance liquid regularly, keep the machine in good condition, especially when it is not used for a long time, prevent the machine from being damaged by damp;
以上就是立式玻璃钻铣机日常维护与玻璃钻孔机日常保养方法相关内容的介绍了。玻多多商城表示，不管是什么玻璃机械设备，在玻璃加工与深加工当中起着非常重要的作用，所以要多积累经验，一旦出现问题，可以及时对症下药。
The above is the vertical glass drilling and milling machine daily maintenance and glass drilling machine daily maintenance method related content is introduced. Boduo mall said that no matter what glass machinery and equipment are, they play a very important role in glass processing and deep processing, so we should accumulate more experience, and in case of problems, we can find the right medicine in time.