进行玻璃加工，玻璃机械是必不可少的设备，玻璃机械包括热弯炉、玻璃磨边机、玻璃钢化炉、玻璃中空线、玻璃钻孔机等。什么是立式玻璃钻铣机？立式玻璃钻铣机使用方法和注意事项，接下来我们一起了解一下。
For glass processing, glass machinery is essential equipment, including hot bending furnace, glass edging machine, glass tempering furnace, glass hollow line, glass drilling machine, etc. What is vertical glass drilling and milling machine? Vertical glass drilling and milling machine use methods and precautions, next let's understand.
立式玻璃钻铣机由PLC自动控制，在操作过程中，只需将玻璃放在传送带上，输入钻孔位置数据，启动按钮，自动定位后钻所有定位孔，完成工作后自动停止工作。
The vertical glass drilling and milling machine is automatically controlled by PLC. In the operation process, just put the glass on the conveyor belt, input the drilling position data, start the button, drill all the positioning holes after automatic positioning, and stop the work automatically after completing the work.
玻璃钻铣机钻孔效率高，孔位准确，适用于建筑玻璃和家具玻璃等常见玻璃的加工；彩色人机触摸屏操作自动控制，界面清晰，操作简便，参数设置一次即可完成处理；PLC程序控制，具有自动检测和诊断功能，电路稳定高性能，在操作环境中具有很高的适用性，并且可以进行远程维护和升级。

Glass drilling and milling machine has high drilling efficiency and accurate hole position, which is suitable for processing common glass such as architectural glass and furniture glass; The operation of color human-machine touch screen is controlled automatically, the interface is clear, the operation is simple, and the parameters can be set once; PLC program control, with automatic detection and diagnosis function, circuit stability and high performance, has high applicability in the operating environment, and can carry out remote maintenance and upgrade.

玻璃钻铣机使用方法：
How to use glass drilling and milling machine:
1、在钻玻璃时，下部钻头很容易挤压玻璃。因此，在打薄玻璃时，必 须将压力调得很低，可以在0.18〜03MPa的范围内改变。当钻厚玻璃时，压力可升高到约0.46MPa。
1. When drilling glass, it is easy for the lower drill bit to squeeze the glass. Therefore, when thinning the glass, the pressure must be adjusted very low, which can be changed in the range of 0.18 ~ 03mpa. When drilling thick glass, the pressure can rise to about 0.46mpa.
2、在每次换档开始之前，应向润滑部件中注入润滑油，并检查皮带的松紧度，上下钻轴是否运转异常以及钻头是否磨损。只有在一切正常之后才能开始工作。
2. Before the start of each shift, the lubricating oil should be injected into the lubricating parts, and the tightness of the belt, whether the upper and lower drill shafts operate abnormally and whether the drill bit is worn should be checked. You can't start working until everything is OK.
3、应及时清理接收抽屉中的芯材，否则太多的芯材会堵塞接收器。特别是在钻出直径大于100mmj的大孔时，请清理每钻几个孔。
3. The core material in the receiving drawer should be cleaned in time, otherwise too much core material will block the receiver. Especially when drilling large holes with diameter larger than 100mmj, please clean up every few holes drilled.
4、玻多多表示，清洁芯材时，收集器应处于收集位置，以使收集抽屉能够顺畅地抽出。因此，在清洁型芯材料时，必 须使用钻头开始旋转。此时，捕集器处于捕集位置，可以轻松清洁物料芯。
4. Boduo said that when cleaning the core material, the collector should be in the collection position so that the collection drawer can be pulled out smoothly. Therefore, when cleaning the core material, the bit must be used to start rotation. At this time, the catcher is in the capture position, which can easily clean the material core.
玻璃钻铣机注意事项：
Precautions for glass drilling and milling machine:
1、调试和使用过程中要注意安 全，开机时切勿触摸活动部件和带电部件；
1. Pay attention to safety during debugging and use. Do not touch moving parts and live parts when starting up;
2、请勿将工具和其他物品放在输送导轨和盖板上；
2. Do not put tools and other items on the guide rail and cover plate;
3、在紧急情况下，立即按下“紧急停止”按钮或拉下空气开关；
3. In case of emergency, press the "emergency stop" button or pull down the air switch immediately;
4、始终保持水箱中有足够的冷 却水和清洁水质，以免烧 伤砂轮和玻璃，并及时清理进水管和出水管中的研磨杂质，以保持水路畅 通；
4. Always keep enough cooling water and clean water in the water tank, so as not to burn the grinding wheel and glass, and clean the grinding impurities in the inlet pipe and outlet pipe in time, so as to keep the waterway smooth;
5、在每次轮班工作之前，检查所有行程开关是否工作正常，控制方向是否正确。如果不正确或控制方向不正确，请立即停止机器进行检查，否则将严重损坏机器。
5. Before each shift, check whether all travel switches work normally and whether the control direction is correct. If it is not correct or the control direction is not correct, stop the machine immediately for inspection, otherwise the machine will be seriously damaged.
6、电机温度：小于或等于50°C的环境温度。
6. Motor temperature: ambient temperature less than or equal to 50 ° C.