生产的中空玻璃加工设备可以高能地完成中空玻璃的生产，在中空玻璃加工行业里享有很高的声誉。俗话说，没有规矩不成方圆，所有设备都有自己的操作规程和规范。操作员在操作中空玻璃生产线的时候，要严格按照中空玻璃加工设备的操作规程来做，那么中空玻璃加工设备的操作规程有哪些，请注意下面几条：
The insulating glass processing equipment can complete the production of insulating glass with high energy, and enjoys a high reputation in the insulating glass processing industry. As the saying goes, there is no square without rules. All equipment has its own operating procedures and specifications. When operating the insulating glass production line, the operator shall strictly follow the operating procedures of the insulating glass processing equipment. What are the operating procedures of the insulating glass processing equipment? Please pay attention to the following:

1.中空玻璃生产线开机顺序：首先要检查中空玻璃加工设备水箱里的水充足，然后打开水泵，调整白色海绵辊上方的喷水管，保证海绵辊所有位置都能被冲洗到。然后用手将海绵辊上的杂质和脏物清洗干净，并且保证海绵辊被完全泡开泡膨胀。注意在冬天开启中空玻璃生产线时，一定不要先打开清洗传送。因为冬天两个紧邻的海绵辊会被冻在一起，在没有被浸泡开的情况下打开传送，会导致海绵辊被撕坏。

1. Startup sequence of insulating glass production line: first check that the water in the water tank of insulating glass processing equipment is sufficient, then turn on the water pump and adjust the water spray pipe above the white sponge roller to ensure that all positions of the sponge roller can be flushed. Then clean the impurities and dirt on the sponge roller by hand, and ensure that the sponge roller is completely foamed and expanded. Note that when opening the insulating glass production line in winter, do not open the cleaning conveyor first. Because two adjacent sponge rollers will be frozen together in winter, opening the transmission without being soaked will cause the sponge roller to be torn.
2.然后打开清洗传送，将待加工的中空玻璃放在传送轮上，注意玻璃一定要放平稳，防止玻璃在传送过程中掉落伤到人。
2. Then open the cleaning conveyor, place the hollow glass to be processed on the conveyor wheel, and pay attention to the glass must be placed stably to prevent the glass from falling and hurting people during transmission.
3.铝隔条上涂抹的丁基胶要保证均匀，而且涂抹在整个铝条表面，防止漏胶，有毛刺现象。并且采用优良丁基胶保证铝条和玻璃结实的站合在一起。铝隔条涂完胶后禁止有粘上灰尘。
3. Butyl glue applied on the aluminum spacer strip shall be uniform and applied on the whole surface of the aluminum strip to prevent glue leakage and burr. And it adopts excellent butyl glue to ensure that the aluminum strip and glass stand together firmly. It is forbidden to stick dust on the aluminum spacer after coating.
4.双组份密封胶要涂抹牢固，表面保持平滑，尤其是拐角处要涂抹好，防止漏气，跑气现象。
4. The two-component sealant shall be applied firmly and the surface shall be smooth, especially at the corners to prevent air leakage and air escape.