很多中空玻璃生产线客户反应，购买中空玻璃生产线后，由中空玻璃生产线厂家派人调试，但是，不知道如何确定中空玻璃生产线已经调试完备，正常生产，在这里，威力智能本着为客户负责，将调试过程全盘公布，希望为大家解惑：
Many customers of the insulating glass production line reported that after purchasing the insulating glass production line, the manufacturer of the insulating glass production line sent someone for debugging. However, I don't know how to determine that the insulating glass production line has been fully debugged and produced normally. Here, Weili intelligence is responsible for the customer and announces the whole debugging process. I hope to solve your doubts:
1、将中空玻璃生产线轻置于安装位,正确摆放生产线各段的位置次序.
1. Place the insulating glass production line lightly at the installation position and correctly place the position order of each section of the production line
2、将中空玻璃生产线的机身调平.调整机器底座上调平螺栓高度,使传送辊、支撑尼龙轮支撑面等高,斜架上的背靠轮共面,各段相对平行,然后锁紧螺母.

2. Level the machine body of the insulating glass production line, adjust the machine base, adjust the height of the leveling bolt, make the supporting surface of the conveying roller and the supporting nylon wheel equal, the back-up wheels on the inclined frame are coplanar, and each section is relatively parallel, and then lock the nut

3、将中空玻璃生产线各段间需联接的部位联接紧固,联接好由入料段到清洗干燥段的传动链条.正确摆放风机及水箱,并按水路、风路系统图接好风管、水管.
3. Fasten the parts to be connected between the sections of the insulating glass production line, connect the transmission chain from the feeding section to the cleaning and drying section, correctly place the fan and water tank, and connect the air pipe and water pipe according to the water and air circuit system diagram
4、全 面检查中空玻璃生产线所有紧固件连接处是否因运输震动而松动,并逐件紧固(特别是各接线端子连接处是否松动).
4. Comprehensively check whether all fastener connections of the insulating glass production line are loose due to transportation vibration, and tighten them one by one (especially whether the connections of each wiring terminal are loose)
5、接地线用截面积不小于4平方毫米的软铜心黄绿绝缘线,接地电阻不大于4欧姆.
5. The grounding wire shall be soft copper core yellow green insulated wire with a cross-sectional area of not less than 4mm2, and the grounding resistance shall not be greater than 4 ohms
接通气源检查管路是否通畅,有无破损.气源压力要求0.6~0.8Mpa.接通电源试验中空玻璃生产线各电机的旋转方向是否正确,各段传动链轮是否灵活、平稳.整机清洁,整理工作区间.
Connect the air source and check whether the pipeline is unobstructed and damaged. The air source pressure is required to be 0.6 ~ 0.8MPa. Connect the power supply and test whether the rotation direction of each motor of the insulating glass production line is correct and whether the transmission sprocket of each section is flexible and stable. Clean the whole machine and sort out the working range
以上就是我们调试人员所需要做并且确定做到的中空玻璃生产线的调试，选择中空玻璃生产线，还是选择真 正的厂家，只有真 正的厂家，价格才能优惠，性价比才会更好，毕竟没有一个厂家生产出中空玻璃生产线，是奔着自己倒闭的，您说呢，中空玻璃生产线厂家还是选择威力智能，质量优，运行稳定可靠。
The above is what our commissioning personnel need to do and decide to do. Choose a hollow glass production line or a real manufacturer. Only a real manufacturer can have preferential prices and better performance price ratio. After all, no manufacturer has produced a hollow glass production line and is going bankrupt. What do you say, The manufacturer of insulating glass production line still chooses power intelligence, excellent quality and stable and reliable operation.