服务热线: 0531-68828688
新闻资讯
您当前位置: 首页 - 新闻资讯 - 行业快讯
企业新闻行业快讯政府关怀党政活动
浅谈中空玻璃设备的设计理论!

2021.08.10威力智能

在玻璃材料给定后,比如普通玻璃或钢化玻璃,那么根据玻璃强度设计理论,玻璃原片的断裂强度就确定下来了。由于中空玻璃机器生产的玻璃是由两片(或两片以上)玻璃构成,周边密封形成一个密封的空气层。

After the glass material is given, such as ordinary glass or toughened glass, the breaking strength of the original glass sheet is determined according to the glass strength design theory. As the glass produced by the insulating glass machine is composed of two (or more) pieces of glass, the surrounding seal forms a sealed air layer.

中空玻璃在一面玻璃受到载荷作用时,受力面玻璃变形压缩中空层气体,气体压强增加,将部分载荷传送给另一面玻璃,因此在气体密封状态下,中空玻璃是两片玻璃共同承担载荷,两片玻璃同时变形。中空玻璃是两层或多层平板玻璃由灌注了干燥剂的铝框用丁基胶和聚硫胶粘结而成。
When one side of the insulating glass is subjected to load, the glass on the stress surface deforms and compresses the gas in the insulating layer, the gas pressure increases, and part of the load is transmitted to the other side of the glass. Therefore, in the gas sealed state, the insulating glass is two pieces of glass to bear the load together, and the two pieces of glass deform at the same time. Insulating glass is two or more layers of flat glass, which is made of aluminum frame filled with desiccant and bonded with butyl glue and polysulfide glue.
制造中空玻璃设备的原片玻璃可以是无色浮法玻璃、镀膜玻璃、钢化玻璃、夹层玻璃等。应避免使用普通平板玻璃,普通平板玻璃的透明度及强度均达不到要求。
The original glass for manufacturing insulating glass equipment can be colorless float glass, coated glass, tempered glass, laminated glass, etc. The use of ordinary flat glass shall be avoided. The transparency and strength of ordinary flat glass cannot meet the requirements.
上述玻璃原片必 须符合相应标准要求,经检验合格后才能使用。不同厂家不同批次的玻璃在切割前应首先检查有无色差,将色差较大的玻璃分别用于不同的工程或不同的建筑立面中。
The original glass sheet must meet the requirements of corresponding standards and can be used only after passing the inspection. Before cutting different batches of glass from different manufacturers, first check whether there is color difference, and use the glass with large color difference in different projects or different building facades.
玻璃切割尺寸应按图纸要求严格执行,同时操作人员应注意玻璃表面,不得有划伤、气泡等明显缺 陷。铝条、插角的选用:铝条的厚度应在0.30mm~0.35mm之间,厚度应均匀一致,透气孔分布均匀。铝条须经阳极氧化处理或去污处理,一定要选用质量好、档次高的产品,提高铝条利用率。
The glass cutting size shall be strictly implemented according to the requirements of the drawing. At the same time, the operator shall pay attention to the glass surface without obvious defects such as scratches and bubbles. Selection of aluminum strip and insertion angle: the thickness of aluminum strip shall be between 0.30mm and 0.35mm, the thickness shall be uniform, and the vent holes shall be evenly distributed. Aluminum strips must be anodized or decontaminated. Products with good quality and high grade must be selected to improve the utilization rate of aluminum strips.
联系我们

全国销售热线:

0531-68828688 87987918

邮箱:jnweljq@weiliglass.com

地址:

山东省德州市齐河县刘桥镇齐刘路002号

立即订购

山东省德州市齐河县刘桥镇齐刘路002号
0531-68828688 87987918
www.weiliglass.com